In Stock

GWInstek GPT-9503 AC 150VA Multi-Channel Hipot Tester (AC/DC/IR) Channel Status H or X

Available for Quote

150VA Multi-channels Hipot Tester (H or X)

  • Multi-channel hipot tester
  • Channel status – H or X
  • AC withstanding – 0.05-5kV
  • DC withstanding – 0.05-6kV
  • Insulation resistance – 50-1000V DC / 0.1M – 10G Ω
  • 150VA AC test capacity
  • Built in 8 channel scanner
  • Open / short check (OSC)
  • Arc detection
  • Interface: RS-232C and USB host/device

More Info

Quick Comparison

SettingsGWInstek GPT-9503 AC 150VA Multi-Channel Hipot Tester (AC/DC/IR) Channel Status H or X removeAmprobe SC-3500 4? Signal Clamp for AT-3500 removeAEMC 6527 4G Ohm, 250V/500V/1000V Digital Megohmmeter removeAmprobe AT-6000-T Transmitter removeAmprobe MLS55-3 Pipe Transmitter for AT-3500 removeAmprobe LM-120 Light Meter remove
ImagePlaceholder
SKUN_GW Instek GPT-9503N_Amprobe SC-3500N_AEMC 6527N_Amprobe AT-6000-TN_Amprobe MLS55-3N_Amprobe LM-120
Rating
PriceAvailable for QuoteAvailable for QuoteAvailable for QuoteAvailable for QuoteAvailable for QuoteAvailable for Quote
Stock
Availability
Add to cart

Add to cart

Add to Cart

Add to Cart

Add to Cart

Add to Cart

Add to Cart

Description

150VA Multi-channels Hipot Tester (H or X)

  • Multi-channel hipot tester
  • Channel status - H or X
  • AC withstanding - 0.05-5kV
  • DC withstanding - 0.05-6kV
  • Insulation resistance - 50-1000V DC / 0.1M - 10G Ω
  • 150VA AC test capacity
  • Built in 8 channel scanner
  • Open / short check (OSC)
  • Arc detection
  • Interface: RS-232C and USB host/device
More Info
ContentThe Amprobe SC-3500 4? Signal Clamp for AT-3500 attaches around a buried metallic pipe, cable, or wire to induce a transmitted signal into the feature for active location and tracing. It does not require direct contact with metal to transmit the signal and can transmit signal through insulation on wires and into cable and wire bundles, providing more accurate tracing than locating with just a receiver and transmitter. Accommodates conductors up to 4? in diameter. Transmits a 33 kilohertz (kHz) frequency supplied by the T-3500 Transmitter (included in the AT-3500 kit).The AT-6000-T Transmitter works on Energized and De-energized circuits up to 600 V AC/DC in Category I through Category III electrical environments and features high signal, low signal, and loop modes. The Breaker Identification feature eliminates confusion of multiple false positives, common with older technology tracing tools, by identifying the one correct breaker or fuse with the highest recorded signal.The Amprobe MLS55-3 Pipe transmitter is an optional accessory for the AT-3500 underground cable locator that allows for pinpointing places in pipes, ducts, etc. It can be inserted to the pipe/duct using standard fish tape or a duct rodder and can accommodate pipes over 2? (5 cm) in diameter.The Amprobe LM-120 light meter measures the visible light from fluorescent, metal halide, high-pressure sodium or incandescent sources. It is a portable, easy-to-use digital light meter designed for simple one-hand operation reading in Lumen (lux) or foot candle (fc) units. The LM-120 measures a wide range of light up to 20,000 fc or 200,000 lux with an accurate, high resolution of 0.01 fc/lux. This unit is Auto-ranging plus manual ranging with ability to Zero out the reading before taking a measurement.
Weight4622111
Dimensions12 × 18 × 24 in9.84 × 9.84 × 9.84 in10 × 5 × 5 in9.5 × 6.5 × 1.75 in7.1 × 5.3 × 3.7 in4 × 10 × 2 in
Additional information
Weight 46 lbs
Dimensions 12 × 18 × 24 in
Weight 2 lbs
Dimensions 9.84 × 9.84 × 9.84 in
Weight 2 lbs
Dimensions 10 × 5 × 5 in
Weight 1 lbs
Dimensions 9.5 × 6.5 × 1.75 in
Weight 1 lbs
Dimensions 7.1 × 5.3 × 3.7 in
Weight 1 lbs
Dimensions 4 × 10 × 2 in